DatasheetBay.com



B-13-155-T-SXX3 (LuminentOIC) : Total 8 Pages

No Preview Available !

[ Download PDF for PC ]

155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
Absolute Maximum Rating
Parameter
Power Supply Voltage
Power Supply Voltage
Input Voltage
Output Current
Soldering Temperature
Storage Temperature
Symbol
Vcc
Vcc
-
Iout
-
Tstg
Recommended Operating Condition
Parameter
Symbol
Power Supply Voltage
Power Supply Voltage
Operating Temperature (Case)
Operating Temperature (Case)
Data Rate
Vcc
Vcc
Topr
Topr
-
Min.
0
0
0
-
-
-40
Min.
4.75
3.1
0
-40
-
Features
• Diplexer Single Mode Single Fiber 1x9 SC/FC/ST Receptacle
Connector
• Wavelength Tx 1310 nm/Rx 1530 nm
• SONET OC-3 SDH STM-1 Compliant
• Single +5V/+3.3V Power Supply
• PECL/LVPECL Differential Inputs and Output
[B-13/15-155-T(3)-Sxx3(4)]
• TTL/LVTTL Differential Inputs and Output
[B-13/15-155C-T(3)-Sxx3(4)]
• Wave Solderable and Aqueous Washable
• LED Multisourced 1x9 Transceiver Interchangeable
• Class 1 Laser Int. Safety Standard IEC 825 Compliant
• Uncooled Laser diode with MQW structure
• Complies with Telcordia (Bellcore) GR-468-CORE
• RoHS compliance available
Max.
6
3.6
Vcc
30
260
85
Unit
V
V
V
mA
ºC
ºC
Note
B-13/15-155(C)-T-Sxx3(4)
B-13/15-155(C)-T3-Sxx3(4)
10 seconds on leads only
Typ.
5
3.3
-
-
155
Max.
5.25
3.5
70
85
-
Unit
V
V
ºC
ºC
Mbps
Transmitter Specifications
Parameter
Optical
Optical Transmit Power
Optical Transmit Power
Output center Wavelength
Output Spectrum Width
Extinction Ratio
Output Eye
Optical Rise Time
Optical Fall Time
Optical Isolation
Relative Intensity Noise
Total Jitter
Symbol Min Typical Max Unit
Notes
Po -14
-
-8
dBm
Output power is coupled into a 9/125 µm
single mode fiber.B-13/15-155(C)-T(3)-Sxx3
Po -8
-
-3
dBm
Output power is coupled into a 9/125 µm
single mode fiber.B-13/15-155(C)-T(3)-Sxx4
λ
1260
1310
1360
nm
∆λ - - 3 nm RMS (σ)
ER 8.2
-
- dB
Compliant with ITU-T recommendation G.957/STM-1
Tr - - 2 ns 10% to 90% Values
Tf - - 2 ns 10% to 90% Values
- 30 -
- dB Tx:1530 nm/ Rx:1310 nm
RIN -
-
-116
dB/Hz
TJ -
-
1.2
ns
Measured with 223-1 PRBS with 72 ones and
72 zeros.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS591-Apr2007
Rev A.2



No Preview Available !

[ Download PDF for PC ]

155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
Transmitter Specifications
Parameter
Electrical
Power Supply Current
Data Input Current-Low
Data Input Current-High
Differential Input Voltage
Data Input Voltage-Low
Data Input Voltage-High
Symbol Min Typical Max
ICC -
- 140
IIL -350
-
-
IIH -
- 350
VIH-VIL
VIL-VCC
300
-2.0
--
- -1.58
VIH-VCC
-1.1
- -0.74
Unit
Notes
mA
Maximum current is specified at Vcc=
Maximum @ maximum temperature
µA
µA
mV
V These inputs are compatible with 10K,
V 10KH and 100K ECL and PECL inputs
Receiver Specifications
Parameter
Optical
Sensitivity
Maximum Input Power
Signal Detect-Asserted
Symbol Min Typical
--
Pin -3
Pa -
-
-
-
Signal Detect-Deasserted
Pd -45
-
Signal Detect-Hysteresis
1.0 -
Cross Talk
Wavelength of Operation
---
1480
-
Note 1: The SD level should be deasserted when fiber disconnected
Max
-33
-
-33
-
4.0
-33
1600
Unit
Notes
dBm
dBm
dBm
dBm
dB
dB
nm
Measured with 223-1 PRBS, BER = 10-10
Measured on transition: low to high
(Note1)
Receiver Specifications
Parameter
Electrical
Symbol
Power Supply Current
ICC
Data output Voltage-Low
Data output Voltage-High
Signal Detect output Voltge-Low
Signal Detect Output Voltge-High
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
VOL -Vcc
VOH- Vcc
VSDL-Vcc
VSDH- Vcc
VSDL
VSDH
Min
-
-2.0
-1.1
-2.0
-1.1
-
2.0
Typical
-
-
-
-
-
-
-
Max
100
-1.58
-0.74
-1.58
-0.74
0.5
-
Unit
Note
mA
The current excludes the output load
current
V These outputs are compatible with 10K,
V 10KH and 100KECL and PECL outputs
V
V
B-13/15-155-T(3)-Sxx3(4)
V B-13/15-155C-T(3)-Sxx3(4)
V
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS591-Apr2007
Rev A.2



No Preview Available !

[ Download PDF for PC ]

155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
Connection Diagram
1. (Rx GND)
2. (Rx +)
3. (Rx-)
4. (SD)
5. (Rx Vcc)
6. (Tx Vcc)
7. (TX-)
8. (TX+)
9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN
1
2
3
4
5
6
7
Warning8s
9
Symbol
RxGND
RD+
RD-
SD
RxVcc
TxVcc
TD-
TD+
TxGND
Notes
Directly connect this pin to the receiver ground plane
See recommended circuit schematic
See recommended circuit schematic
Active high on this indicates a received optical signal
DC power for the receiver section
DC power for the transmitter section
See recommended circuit schematic
See recommended circuit schematic
Directly connect this pin to the transmitter ground plane
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS591-Apr2007
Rev A.2



No Preview Available !

[ Download PDF for PC ]

155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
Recommended Circuit Schematic (3.3V/5V)
B-13/15-155-T(3)-Sxx3(4)
Tx Vcc
C5
R1 R3
9 8 7 65 43 2 1
TD +
TD -
R2 R4
Notes +3.3V:
R1=R3=R5=R7=R9=130
R2=R4=R6=R8=R10=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Tx Vcc
Rx Vcc
No internal
connection
Transceiver
Top view
No internal
connection
Notes +5V:
R1=R3=R5=R7=R9=82
R2=R4=R6=R8=R10=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Vcc
Rx Vcc
R9 R5 R7
R10 R6 R8
C6
RD +
RD -
SD
L1
C3
L2
C4
Rx Vcc
C1
Tx Vcc
C2
Recommended Circuit Schematic (3.3V/5V)
B-13/15-155C-T(3)-Sxx3(4)
Tx Vcc
C5 R1 R3
9 8 7 65 43 2 1
TD +
TD -
R2 R4
Tx Vcc
Rx Vcc
No internal
connection
Transceiver
Top view
No internal
connection
Notes +3.3V:
R1=R3=R5=R7=130
R2=R4=R6=R8=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Notes +5V:
R1=R3=R5=R7=82
R2=R4=R6=R8=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Vcc
Rx Vcc
R5 R7
R6 R8
C6
RD +
RD -
SD
L1
C3
L2
C4
Rx Vcc
C1
Tx Vcc
C2
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS591-Apr2007
Rev A.2






[ Download PDF for PC ]






0  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z  

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
* 2015 :: DatasheetBay.com :: DatasheetBay